R36S Problems and Troubleshooting
Stock SD Cards
-
stock SD cards -
stock SD cards
-
stock SD cards - device bought at Flipkart (India) -
stock SD card - Source: reddit
.webp)
There have also been reports of these cheap cards overheating and destroying the screen.
✅ Solution
Use quality/branded microSD cards. Please refer to the SD Cards section and Compatibility List or check out the buying guide.
Hardware clones
A lot of problems are caused by Hardware clones. Those "fake" EmuELEC R36S are basically a different device in the R36S shell.
See the R36S Clones page for how to know if you have a clone, working custom firmwares and more info.
Black Screen
⚠️ Cause
Wrong "device tree blob" files (.dtb) in the BOOT partition. There are at least 5 different screen versions for the R36S.
✅ Solution (ArkOS)
You need to use the correct .dtb file. After flashing ArkOS Community Maintained Image to the SD card and before booting up your device, replace the 📄rk3326-r35s-linux.dtb file in the 📁BOOT partition with the one from your original/stock SD card (see Backup).
In case you didn't backup your original 📄rk3326-r35s-linux.dtb file, here's a link to all the different versions: R36S-Device Tree Blob
✅ Solution (AmberELEC)
Rename your original 📄rk3326-r35s-linux.dtb to 📄rk3326-rg351mp-linux.dtb and replace this file on the 📁AMBRELC partition. If you have no sound, use the .dtb files from this link: new DTB files for AmberELEC or use this to fix the sound + the FN button: Panel 4 (V5) AmberELEC sound + FN button fix
✅ Further Troubleshooting
- Try the Panel 4 (V5) version of ArkOS Community Maintained Image
- Make sure you are using the correct dtb file with the correct name
- Delete all .dtb, .tony, .orig and boot.ini files, then copy/paste the dtb files plus the boot.ini from your stock SD card
- Re-flash every time you try different .dtb files
- Replace the .dtb file before booting up the first time
- Delete the .dtb file first instead of replacing it
- Use a different tool for flashing (Rufus, Win32DiskImager, ApplePi-Baker). balenaEtcher is not recommended
- Flash the firmware image on a different PC or with a Android device
- Use a different microSD card
✅ Black Screen Fix Step by Step Guide
This is a slightly modified guide by u/FreshNoobAcc
- Make sure device has been charged for several hours with a usb A to usb C charger (cable that came with device).
- Flash ArkOS (/or EmulELEC if clone) onto branded SD card. Make sure you are flashing the decompressed ArkOS (/EmulELEC if clone). It should not end in .xz, if it does, decompress it with a program like 7zip.
- Put SD card into device after flashing ArkOS (/EmulELEC if clone).
- Turn on device. Important: leave the device ON for 10 minutes, even if the device shows a black screen, it should be expanding the OS file and working away even if the screen is black. If you see black screen and turn device off too soon, you will corrupt the OS and have to start from step 1 again
- After about 10 minutes, turn device off with the off button (btw, once screen works, try to never do this, always turn off in the game menu)
- Plug SD into computer
- Important: delete all .dtb, .tony, .orig files in the OS partition (if you can’t see it you need to follow the youtube video to find out how to unhide the OS partition with MiniTool Partition Wizard)
- Only after deleting the above files (basically any file that has dtb in the name), copy/paste the dtb files from your stock OS card to the new branded SD card. (There is not always a 1:1 switch, some OS have 3-4 dtb files, others only 2, that is ok).
If you don’t have them (corrupted stock OS card), follow warning 3 in the reddit sidebar and copy/paste in one set of dtb files at a time from the github repository, (one panel at a time) and test the branded SD in the device (see if it turns on) after each copy/paste of dtb files from a panel folder. Best start with newer (higher number) panels and work backwards
- Eject SD. Then plug SD back into r36s
The good thing about this method is if you don’t know which dtb files your device needs (if your SD is DOA) you can quickly swap out/in new dtb files from the github repository (see warning 3 in the reddit sidebar) to test them and don’t necessarily need to re-flash the OS every time you want to test new dtb files (saves about 10 minutes per attempt)
Stuck On The Bootlogo
-
stock SD card boot logo -
stock SD card boot logo -
⚠️ Cause
SD card problem. That's the bootlogo from the stock SD cards with an outdated firmware.
✅ Solution
Change the SD Card.
Stuck During Loading Emulationstation
⚠️ Cause
SD card problem (corrupted roms/bios or other files)
✅ Solution
Change the SD Card or re-flash your good card.
White Lines
-
Source: reddit -
Source: reddit -
Source: reddit -
same error on POWKIDDY RGB20S
⚠️ Cause
Battery is empty. It says something like "Voltage level low" if you look closely.
✅ Solution
Charge the device with a 5V 1.5A-2A adapter and a USB-A to USB-C cable. Charging via Computer/Laptop USB ports also works fine.
"booting fail! check kernel and dtb images!" error at boot logo
⚠️ Cause
SD card problem.
✅ Solution
Change the SD Card.
Small Blinking Line / Blinking Cursor
⚠️ Cause
Blinking Cursor = Looking for TF2 (roms) SD card
- Defect SD card in TF2 slot (most of the times)
- Can happen after upgrading
- Wrong card setting in the menu
✅ Solution
Change the defect TF2 SD card or re-flash the TF1 SD Card.
[Not very likely] If both cards are good you can change the rom card slot via a script. Read the comments in this thread for a possible solution.
Themes Keep Disappearing
⚠️ Cause
SD card problem - SD card is slowly corrupting/dying
✅ Solution
Change the SD Card
Stuck on Boot
-
Source: reddit
⚠️ Cause
Another SD card problem
✅ Solution
Change the SD card
Stuck in RetroArch
-
different RetroArch "menu driver"
⚠️ Cause
Accidentally enabled the option to use RetroArch as the main frontend.
✅ Solution
Reboot the device and hold B to enter "Boot and Recovery Tools" (BaRT) and choose "Emulationstation".
-
Hold B button during boot to enter this menu (ArkOS)
No Gamepads Detected
-
error during boot
⚠️ Cause
Wrong .dtb or boot.ini file
SD card problem
Firmware problem
✅ Solution
Re-flash the firmware, Use the correct .dtb file or change the R36S SD Card.
This error can also be fixed by replacing the boot.ini file (see this comment)
Joystick Problems - Stick Drift
⚠️ Cause
Common problem in lots of controllers. Can have different causes.
loose connector cable
defective joystick
SD card / software related problem
✅ Solution
Read this thread for possible solutions or look for threads with similar problems.
-
connector cable
Saving not working / Can't save / Stuck at saving
Problems with saving can have different causes.
⚠️ Cause
SD card problem
Bad rom dumps (from the stock sd cards)
Can also be a user error like not shutting down the device correctly which can cause problems.
✅ Solution
Change the SD card
Change the bad roms that were included in the stock SD card
Shut down your device safely from within the menu or the FN+Power hotkey
Don't press the reset button to exit your game
Emulator Settings Keep Resetting
✅ Don't forget to save the RetroArch configuration file after changing things or use overrides.
Error Message During Boot (EmuELEC clone)
✅ Solution: Install one of the available custom firmware for R36S clones to a new SD card.
Stuck During Boot (EmuELEC clone)
✅ Solution: Install one of the custom firmware for R36S clones to a new SD card.
Red blinking light during boot (EmuELEC clone)
This happens when you install the standard (or community maintained) ArkOS custom firmware on a EmuELEC clone.
✅ Solution: Install one of the custom firmware for R36S clones to a new SD card.
No rk3326-r35s-linux.dtb or rk3326-rg351mp-linux.dtb on SD card (EmuELEC clone)
-
different files on the Boot partition
If your stock SD card has the 📄rk3326-evb-lp3-v12-linux.dtb or 📄rf3536k3ka.dtb file, you got the EmuELEC Clone that is not compatible with standard ArkOS or AmberELEC custom firmware. See the R36S Clones page for more info.
Other Projects at the Handhelds Wiki
